FrSky TD SR10 Tandem ADV Stabilized Receiver
When long-range control and self-leveling stability both matter on the same flight, the TD SR10 ADV delivers both in one compact package. Running 2.4GHz and 900MHz simultaneously, this Tandem dual-band receiver keeps you in solid RF contact across vast distances while the built-in ADV gyro stabilizer keeps your aircraft flying level when you need it most.
 
The Tandem dual-band system works on both frequencies at the same time — not as a failover. You get the low-latency response of 2.4GHz combined with the range and interference rejection of 900MHz on every flight. The triple antenna design (2x2.4GHz, 1x900MHz) provides multi-directional coverage regardless of aircraft orientation.
 
ADV Stabilizer
The built-in ADV Stabilizer uses a 3-axis gyroscope and accelerometer to add intelligent flight modes — Stabilization, Auto-Level, Hover, and Knife-Edge — to any fixed-wing aircraft without a separate stabilizer unit. The advanced mode allows programmable parameters, stab file sharing, and developer access for complex setups.
 
The 10 configurable channel ports can each be assigned as PWM, SBUS, FBUS, or S.Port. FBUS support means all your ADV sensors daisy-chain on a single wire with live telemetry to your transmitter screen. OTA firmware updates via ETHOS keep the receiver current without any cables.
 
Features
Simultaneous Working Dual-Band (900MHz/2.4GHz) TD Mode
Built-in ADV Stabilizer (3-axis gyro + accelerometer)
10 Configurable Channel Ports (PWM / SBUS / FBUS / S.Port)
SBUS In for Signal Redundancy
Triple Antenna Design (2x2.4GHz + 1x900MHz)
Black Box data recording
Over-The-Air (OTA) firmware updates
4ms Race Mode with Telemetry
Operating Voltage: 3.5-10V DC
Compatibility: Tandem series transmitters and TD-capable RF modules
 
Why We Recommend This
The TD SR10 ADV is our recommendation for pilots stepping up from a standard receiver to something with built-in stabilization — compact, fully dual-band, and ready to simplify any fixed-wing build that previously needed a separate gyro. FPV Builds RC provides U.S.-based product support, receiver-selection assistance, and setup guidance for FrSky products purchased through our store.
Frequently Asked Questions:
 
Which FrSky transmitters are compatible with the TD SR10?
The TD SR10 ADV is compatible with all FrSky Tandem series transmitters: X18, X18S, X18SE, X18RS, X20, X20S, X20RS, X20 Pro, X20 Pro AW, and X20 R. Any radio running the Tandem (TD) protocol or a TD-capable RF module will bind to this receiver. See our full transmitter lineup at https://www.fpvbuildsrc.com/frsky-transmitters
 
What is the ADV Stabilizer and what aircraft is it for?
The ADV Stabilizer is a built-in gyro/accelerometer system that adds self-leveling flight modes (Stabilization, Auto-Level, Hover, Knife-Edge) without a separate stabilizer unit. It's designed for fixed-wing aircraft — warbirds, gliders, trainers, and scale models — where gyro stabilization smooths out turbulence and simplifies recovery.
 
What is the difference between the TD SR10 and the TDR10?
Both use the same Tandem dual-band RF system with 10 configurable channel ports. The TD SR10 ADV adds the built-in gyro stabilizer. The TDR10 is the non-stabilized version — the right pick for aircraft running a dedicated flight controller or builds where you want direct control without onboard gyro processing.
 
Does 900MHz activate automatically?
Yes. Your Tandem transmitter activates the 900MHz link automatically when bound to a TD receiver — no extra setup in ETHOS needed. Both frequencies are live from the first bind.
 
How do I set up FBUS for telemetry sensors?
Assign any channel port to FBUS in your transmitter's ETHOS receiver settings. Then connect your ADV sensors (FAS current sensor, GPS ADV, VARI) to the FBUS port and daisy-chain if needed. Sensor data streams live to your radio display on a single wire. Browse compatible sensors at https://www.fpvbuildsrc.com/frsky-sensors
 
Does the TD SR10 support OTA firmware updates?
Yes. Firmware updates are delivered over-the-air from your Tandem transmitter via ETHOS — no USB cable or PC required.
 
How do I configure the TD SR10's stabilization in ETHOS?
Current FrSky stabilized receivers are configured through the applicable Stabilizer Config/device configuration functions in ETHOS. Receiver orientation, aircraft type, stabilization mode, channel assignments, and related settings should be configured for the specific receiver and aircraft installation. Follow the current FrSky/ETHOS instructions for the TD SR10.
Does FPV Builds RC offer setup support for the TD SR10?
Yes — we're a U.S.-based FrSky dealer happy to help with binding, stabilization setup, and FBUS wiring. Browse our full receiver range at https://www.fpvbuildsrc.com/frsky-receivers